DIN Rail Mounting Plate for Jetson Nano Developer Carrier Board
- Mount your Jetson Nano Developer Carrier Board to DIN rail
- Sturdy construction
- Right-angle design saves valuable space on DIN rail
- Plate size: approx 113.5mm x 93mm
- Screws and nylon standoffs included (M2.5 thread)
- Two sets of mounting holes allow for different mounting orientations
- Extra holes accommodate self-mount cable ties (not included) for strain relief
General Description
Use these sturdy DIN rail mounting plates to mount your device to a standard 35mm DIN rail. This product features a flat plate mounting surface to which you can mount your device, and a metal DIN rail bracket secures the plate to the DIN rail. The pre-drilled holes in the plate make it simple and easy to attach your device to the plate using the included screws and nylon standoffs.
Pre-drilled holes are located to accommodate the Jetson Nano Developer Carrier Board (either with peripheral cables pointing up, or cables pointing down).
The 'right angle' design of this product allows you to mount devices perpedicular to the DIN rail, increasing device density. You can mount Developer Boards at a fraction of the horizontal space they would normally consume.
The mounting plate is made of sturdy 0.125" thick FR4 material (glass-reinforced epoxy laminate material). It comes with a sturdy steel DIN rail bracket (part# DINM30) installed on the plate. The steel brackets may be purchased alone if you desire the bracket without the adapter plate.
These adapter plates are alternately known as DIN rail mounting plates, DIN adapter plates, DIN rail brackets, etc. We sell many varieties of universal DIN rail mounting plates and DIN rail brackets for numerous applications.
Application Examples
The photo below shows a Jetson Nano Developer Board mounted to the DINP03-NV01, which is mounted on a DIN rail. Note that self-mount cable ties can be inserted into predrilled holes on the plate to conventiently strain relief incoming cables.
Click image to enlarge.
Installation and Removal
Mounting your Jetson Device to the Plate
To mount your Jetson device, first attach the nylon standoffs to the plate in the appropriate locations using the included flat-head screws. Then, attach your device to the nylon standoffs using the included pan-head screws.
Installing on DIN Rail
The plate assembly is easily attached and detached from the DIN rail. When on the rail, the steel bracket latches to the rail on both the top and bottom lips of the rail. The bracket should be oriented such that the "fixed" (non spring-loaded) end of the bracket mounts to the top of the DIN rail, thus allowing the fixed end to bear the load. The spring-loaded sliding hooks will then grip the bottom of the DIN rail. This arrangement provides the greatest rigidity and load capacity.
There are two methods for removing the assembly from the DIN rail:
- Release Handle: To remove the plates from a DIN rail using the release handle on the bracket, either pull the handle from the bottom edge of the bracket, or push the handle down from the top edge of the bracket. This releases the sliding hooks that grip the bottom of the rail and allows the bottom edge of the bracket to swing out away from the DIN rail. The entire plate and your mounted device can then be lifted off the DIN rail.
- Push & Pivot: A simpler method, however, is to push up on the mounted device, pivot the top of the device out away from the rail, and lower the entire device off the rail. This technique does not require access to the release handle on the bracket which makes this method easier.
Product Documents
| Part # | Description | PDF Drawing | DWG Drawing | IGES Model | STEP Model |
|---|---|---|---|---|---|
| DINP03-NV01 | DIN Plate, for Jetson Nano Developer Carrier | 
| 
| 
| 
|
DIN Plate, for Jetson Nano Developer Carrier
Product Details
- Plate size: approx 113.5mm x 93mm
- Screws and nylon standoffs included (M2.5 thread)
- Two sets of mounting holes allow for different mounting orientations
- Extra holes accommodate self-mount cable ties (not included) for strain relief
- Constructed of 0.125" thick FR4 material
- 25mm wide right angle steel DIN bracket
- Clips onto 35mm DIN rail
- Color: Black
- DIN Rail, Cable Ties, and Jetson Nano / Developer Carrier Board not included
Pricing and Ordering
| Product # | Description | 1+ | 10+ | 25+ | 50+ | RoHS | Buy Now |
|---|---|---|---|---|---|---|---|
| DINP03-NV01 | DIN Rail Mounting Plate, Right Angle, for Jetson Nano Developer Carrier Board; with Steel Bracket; for 35mm DIN Rail | $17.10 | $16.05 | $15.50 | $15.00 | Yes | |
| CTSMP2R25-4.5x0.10-NAT-10 | Zip Tie, Self-Mount, for 1/16" - 9/64" Nominal Panel Thickness, with 0.25" Riser, Width=0.10", Length=4.5"; Color: Natural, Bag of 10 | $3.00 | $2.80 | $2.80 | $2.80 | Yes |
| Quantity | Price |
|---|---|
| 1+ | $17.10 |
| 10+ | $16.05 |
| 25+ | $15.50 |
| 50+ | $15.00 |
| Quantity | Price |
|---|---|
| 1+ | $3.00 |
| 10+ | $2.80 |
| 25+ | $2.80 |
| 50+ | $2.80 |
All of the above items are normally stocked. Please call us if you need to verify availability for a specific quantity, or for pricing at higher quantities. Please visit our ordering page for our ordering policies and a list of ordering methods.